|
Description:
|
CrystalStones®
Natural Pebble Pool finishes are blends of specially selected natural
pebble aggregates. CrystalStones® provides the proven durability
of natural pebble finishes as an alternative to traditional pool plaster
finishes. CrystalStones® variety in colorfast pigments
and textures offer the customers almost limitless flexibility in poolscape
design. CrystalStones® is easily installed but intended
for use by professional applicators. |
|
Benefits:
|
-
Proven Durability
- Etch Resistant
- Colorful, Variegated Aggregates
- Traditional or Sprayed Applied
- Ease of Maintenance |
|
Preparation:
|
CrystalStones® should
be applied to a sound surface free of oil, dirt, algae or any other
foreign substance. Previously applied paints or sealers must be removed
by acid washing and/or sandblasting. Neutralize acid with baking soda
or soda ash, then thoroughly rinse with water. In addition to, or
in partial replacement of, the procedures mentioned above, CLI PERMAKOTE® could
be used as a bonding coat. Re-finished pools must be undercut an appropriate
distance around all tile, return lines, light fixtures and main drains.
All weepers and plumbing leaks should be repaired at least 24 hours
prior to plaster application (follow NSPI and/or NPC standards). |
|
Mixing:
|
1.
Using standard mixing equipment, it is important to blend each batch
for the same amount of water and to mix each batch for the same amount
of time. This is to ensure consistent color throughout the finish.
1. Mix CrystalStones® with approximately 1 1/2 to 1 3/4
gallons of potable water per 80-lb. bag.
3. Start the mixing procedure by adding approximately 2/3 of the total
water requirements to the mixer; add CrystalStones® to the balance
of water.
4. Mix the completed batch for at least 8 minutes to ensure a proper
blend of all ingredients.
5. Before using any job site additives, please consult your CLI Product
Service Representative at 800-333-2660. |
|
Application:
|
CrystalStones® may
be applied by either spray or conventional methods. Apply CrystalStones®
over a lightly dampened (no standing water) surface to a uniform thickness
of approximately 3/8". Substrate conditions will have a direct
relationship on the thickness of application and coverage rates per
bag. If application must be interrupted, finish to a natural break
to prevent joints from showing. CrystalStones® should be
applied in temperatures exceeding 40† F. |
|
Aggregate
Exposure:
|
After
the cement has hardened sufficiently to prevent excessive aggregate
Exposure: loss, gentle brushing and controlled water flow are applied
to remove the cement surface paste. A diluted muriatic acid solution
is then applied to the surface to finally expose the pebble finish.
Care should be taken to neutralize and dispose of the acid solution
in an environmentally acceptable manner. |
|
Curing:
|
Care
should be taken to protect CrystalStones® from rapid drying
conditions such as high wind, high temperature and low humidity. Such
precautions may include fogging or misting the surface or placing
a protective covering over the pool. Cover should not be placed directly
on pool surface. |
|
Filling
Procedures:
|
When
filling the pool it is important to do so without interruption of
fill water. Fill pool as rapidly as possible. All fill hoses should
have a sock or cloth on the end. Do not allow main hose length to
lay on the aggregate surfaces, as it will leave a mark. |
|
Water
Chemistry:
|
The
pool water must be carefully balanced from the initial fill and constantly
maintained within recommended NSPI guidelines. Maintaining proper
chemical balance from first fill is essential to maximize the life
of the pool surface. Please consult your CLI Product Service Representative
concerning start-up techniques and maintenance programs. |
|
Coverage:
|
Each
80-lb. bag covers approximately 14-20 sq. feet at 3/8" thickness.
Coverage rates may vary depending on method of application and condition
of substrate. |
|
Packaging:
|
CrystalStones®
is packaged in 80-lb. heavy-duty poly-lined bags. |